API 5L/ASTM A53GR B 24″X6.35MMX20FT WELD PIPES

Our company accept payment after material at your warehouse.

We can proceed the payment after received material at your site in 180 days max.

Contact person: Ms. Hellen

Wechat/ WhatsApp: +86-18203173880

Email: hellen@zssteeltube.com

  

SEND INQUIRY

Your e-mail will not be leaked.
You can make an inquiry about this product.

Follow the Trade Assurance process and get:

  • On-time shipment and pre-shipment product quality safeguards.
  • Payment refund up to 100% of the Trade Assurance Order Amount.
  • Trade Assurance coverage.

MECHANICAL PROPERTIES

Mechanical properties

Pipe Grade Tensile Properties – Pipe Body of SMLS and Welded Pipes PSL 1 Seam of Welded Pipe
Yield Strength a Tensile Strength a Elongation Tensile Strength b
Rt0,5 PSI Min Rm PSI Min (in 2in Af % min) Rm PSI Min
A 30,500 48,600 c 48,600
B 35,500 60,200 c 60,200
X42 42,100 60,200 c 60,200
X46 46,400 63,100 c 63,100
X52 52,200 66,700 c 66,700
X56 56,600 71,100 c 71,100
X60 60,200 75,400 c 75,400
X65 65,300 77,500 c 77,500
X70 70,300 82,700 c 82,700
a. For intermediate grade, the difference between the specified minimum tensile strength and the specified minimum yield for the pipe body shall be as given for the next higher grade.
b. For the intermediate grades, the specified minimum tensile strength for the weld seam shall be the same as determined for the body using foot note a.
c. The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be determined using the following equation:
Where C is 1 940 for calculation using Si units and 625 000 for calculation using USC units
Axc   is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches) , as follows
– For circular cross-section test pieces, 130mm2 (0.20 in2) for 12.7 mm (0.500 in) and 8.9 mm (.350 in) diameter test pieces; and 65 mm2 (0.10 in2) for 6.4 mm (0.250in) diameter test pieces.
– For full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2)
– For strip test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2)
U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch)
Pipe Grade Tensile Properties – Pipe Body of SMLS and Welded Pipes PSL 2 Seam of Welded Pipe
Yield Strength a Tensile Strength a Ratio a,c Elongation Tensile Strength d
Rt0,5  PSI Min Rm  PSI Min R10,5IRm (in 2in) Rm (psi)
Af %
Minimum Maximum Minimum Maximum Maximum Minimum Minimum
BR, BN,BQ,BM 35,500 65,300 60,200 95,000 0.93 f 60,200
X42,X42R,X2Q,X42M 42,100 71,800 60,200 95,000 0.93 f 60,200
X46N,X46Q,X46M 46,400 76,100 63,100 95,000 0.93 f 63,100
X52N,X52Q,X52M 52,200 76,900 66,700 110,200 0.93 f 66,700
X56N,X56Q,X56M 56,600 79,000 71,100 110,200 0.93 f 71,100
X60N,X60Q,S60M 60,200 81,900 75,400 110,200 0.93 f 75,400
X65Q,X65M 65,300 87,000 77,600 110,200 0.93 f 76,600
X70Q,X65M 70,300 92,100 82,700 110,200 0.93 f 82,700
X80Q,X80M 80,.500 102,300 90,600 119,700 0.93 f 90,600
a. For intermediate grade, refer to the full API5L specification.
b. for grades > X90 refer to the full API5L specification.
c. This limit applies for pies with D> 12.750 in
d. For intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using foot a.
e. for pipe requiring longitudinal testing, the maximum yield strength shall be ≤ 71,800 psi
f. The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be determined using the following equation:
Where C is 1 940 for calculation using Si units and 625 000 for calculation using USC units
Axc   is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches) , as follows
– For circular cross-section test pieces, 130mm2 (0.20 in2) for 12.7 mm (0.500 in) and 8.9 mm (.350 in) diameter test pieces; and 65 mm2 (0.10 in2) for 6.4 mm (0.250in) diameter test pieces.
–  For full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2)
–  For strip test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2)
   U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch
g. Lower values fo R10,5IRm may be specified by agreement
h. for grades > x90 refer to the full API5L specification.

Global Business

1. More than 10 years of sales experience

2. Product exported more than 150 countries

3. Arrange to produce according yo customer's request

Fast Delivery

1. AA level customs broker,Faster through

2. 20 years of experience in the freight forwarding company

3. Delivery Detail: 10-20 days

Trusted Quality

1. Certificate: API, CE, ISO9001.2000.MTC etc

2. Inspection: BV,SGS,others is avaliable.

3. A complete testing system and testing equipments

One-Step Service

1. Free sample can be provided

2. Small order is acceptable

3. OEM is acceptable

4. Any third party testing is acceptable

 

Email

Tel

  • Phone0086-317-2159105

Fax

  • Phone0086-317-2159106