Max-Pleate A series Filter Cartridge specification
Max-Pleate A Series Filter Cartridge Specification PP Filter are widely used in high quality beer&beverage, Biological products, medical, Pharmaceutical and air filtration.
In different industry with different requirement, Kinda produce PP Filter of WEP/EWPB/HFP/HPP/ APP/PPT series to meet various demands.
Please contact us and tell us your appilication and main factor you thinking about, we not only the filter manufacturer, also provide prossional filtration separation solutions, filtration testing and filtration guidance for globbal customers.
We had supply filter many times to Eskom in SA for the power station!!!
Max-Pleate Filter Cartridge 6 inch A Series Specification
With 6-inch large Diameter and coreless design, Max-Pleat A expands effective filtration area signicantly.
The improved EFA(effective ltration area) will impress you by sharply decreased change-out frequency and obviously smaller operation footprint .
Features – High Flow Rate
6″ diameter, large geometry Larger filtration surface leads to higher flow rate,lower delta pressure and longer service life. Consumable cost and labor expense will be saved.Multi-application suitability covers Cooling Water Filtration, RO Pre-filtration, Seawater Desalination, Amine Circulation Filtraion and kinds of chemical solution filtration.
Features – Cost Saving
High flow capacity reduces upfront capital cost Up to 40 times fewer cartridg to change out Up to 50% smaller filter system possible Handle design leads to much faster, easier Filter changeout
Features – High Dirt Holding Capacity Max-Pleate A Series Filter Cartridge Specification
Depth pleated structure combines multiple filtration medias brings higher dirt holding capacity and absolute retention efficiency.
Inside-out flow pattern design holds most debris in and prevents housing pollution.
Specification
Typical Application Max-Pleate A Series Filter Cartridge Specification
Power Condensate System
Municipal Water
Chemical
Petrochemicals
Electronics (RO Preltration, Process
Water)
Food& Beverage (process Water)
Pharmeceutical (process water)
Waste Water
Note:
Max-Pleate Filter Cartridge 6 inch A SeriesThe test procedure used is an adaptation of ISO 4572, modified to determine themicron size above which particles are quantitatively removed.Pressure drop in PSID per US gpm for the cartridge Length shown. Multiply this valueby the total system flow to determine the aqueous pressure drop. Next for High Flowfiler only;it must be added to the pressure drop due to the Brother High Flow Filter Housing.
Ordering Information Max-Pleate A Series Filter Cartridge Specification
MAHF P 050 40 E
Cartridge Design Media
P=Polypropylene
G=GlassFiber
Removing Rating 010=1um
Length 40=40inch 60=60inch
O ring Material E=EPDM 030=3um V=Fluororubber S=Silicon 050=5um 100=10um 200=20um 400=40um 700=70um
N=Buna-N rubber
4 Brother Max-Pleat A Series
Instructions:Filter Cartridge Specification
To install a filter element, remove the element hold down plate by lifting it off the
locating pins. Lubricate the O-ring on the open-end of the lter with a compatible fluid, and
slide the closed end of the filter into the perforated cage, which is welded to the
tubesheet. Seat the elements in place by pressing down on the open-end of the
filter until the element is snug in the tubesheet.
This provides a Seal between the filter and housing via the filter O-ring.
The open-end Cap must be below the tubesheet surface.
After installing all the filter cartridges, reinstall and secure the element hold down
plate by guiding it over the locating pins on the tubesheet.
The purpose of the hold down plate is to prevent the elements from becoming
dislodged in the event of reverse flow.
A filter element tool is provided with each housing to aid with the installation and
removal of the filter cartridges.
This tool eliminates the need for an operator to reach within the filter vessel to
either remove or install the filters.
Cangzhou Zhongshun steel Pipe Trade Co.,Ltd
Add:Room 101,Custom House Building,Cangzhou City ,Hebei Province,china
Email:lisa@zssteeltube.com
Tel: 0086 18132295089
