Comparing the Properties of ASTM Ss 201, 304, 304L, 316, 316ti, 310S, 309S, 430, 904L, 2205 Stainless steel

ASTM Ss 201, 304, 304L, 316, 316ti, 310S, 309S, 430, 904L, and 2205 are all different grades of stainless steel that are commonly used in various industries. Each grade has its own unique properties and characteristics that make it suitable for specific applications. In this article, we will compare the properties of these stainless steel grades to help you understand their differences and choose the right one for your needs.

OD In (mm)	+	–	WT In (mm)	+	–
<1(25.4)	0.10	0.10	≤1.1/2(38.1)	20%	0
1∼1.1/2(25.4∼38.1)	0.15	0.15	>1.1/2(38.1)	22%	0
>1.1/2∼<2(38.1∼50.8)	0.20	0.20
2∼<2.1/2(50.8∼63.5)	0.25	0.25
2.1/2∼<3(63.5∼76.2)	0.30	0.30
3∼4(76.2∼101.6)	0.38	0.38
>4∼7.1/2(101.6∼190.5)	0.38	0.64
>7.1/2∼9(190.5∼228.6)	0.38	1.14

Starting with ASTM Ss 201, it is a low-cost alternative to traditional stainless steel grades. It has good Corrosion resistance, formability, and weldability. However, it has lower nickel content compared to other grades, which makes it less resistant to corrosion in certain environments.

Moving on to ASTM Ss 304, it is one of the most widely used stainless steel grades. It has excellent corrosion resistance, good formability, and high strength. It is also non-magnetic and can be easily welded. ASTM Ss 304L is a low-carbon version of 304, which offers even better corrosion resistance in welded structures. casing Pipe,casing well pipe, casing supreme pipe, casing vs carrier pipe, casing for ac pipe, casing steel pipe, casing pipe size, casing pvc pipe price, casing pipe, casing pipe suppliers in China, casing capping pipe, casing drill pipe,carrier pipe,casing pipe size,bushing Flange,bushing sleeve,bushing,bushing arm,bushing bearing,bushing Reducer,bushing tool,bushing pvc,bushing meaningASTM Ss 316 is another popular stainless steel grade known for its excellent corrosion resistance, especially in chloride environments. It has higher nickel and molybdenum content compared to 304, which enhances its resistance to pitting and crevice corrosion. ASTM Ss 316ti is a titanium-stabilized version of 316, which

Labels a							Calculated Mass c
			Nominal Linear Mass T& C b,c	Wall Thick- ness				em, Mass Gain or Loss Due to End Finishing d
		Outside Diameter			Inside Diameter	Drift Diameter	Plain- end	kg
								Round Thread		Buttress Thread
							wpe
		D	kg/m	t	D	mm	kg/m	Short	Long	RC	SCC
		mm		mm	mm
1	2	3	4	5	6	7	8	9	10	11	12
13 3/8	48	339.72	71.43	8.38	322.96	318.99	68.48	15.04	—	— 17.91	—
13 3/8	54.5	339.72	81.1	9.65	320.42	316.45	78.55	13.88	—	16.44	—
13 3/8	61	339.72	90.78	10.92	317.88	313.91	88.55	12.74	—	14.97	—
13 3/8	68	339.72	101.19	12.19	315.34	311.37	98.46	11.61	—	14.97	—
13 3/8	68	339.72	101.19	12.19	315.34	311.37	98.46	11.67 f	—	14.33	—
13 3/8	72	339.72	107.15	13.06	313.6	311.15 e	105.21	10.98	—	13.98	—
13 3/8	72	339.72	107.15	13.06	313.6	311.15 e 309.63 309.63	105.21	10.91 f	—	14.33	—
13 3/8	72	339.72	107.15	13.06	313.6		105.21	10.98	—	13.98	—
13 3/8	72	339.72	107.15	13.06	313.6		105.21	10.91 e	—		—
16	65	406.4	96.73	9.53	387.4	382.57	96.73	18.59	—	— 20.13	—
16	75	406.4	111.61	11.13	384.1	379.37	108.49	16.66	—	18.11	—
16	84	406.4	125.01	12.57	381.3	376.48	122.09	14.92	—	—	—
16	109	406.4	162.21	16.66	373.1	368.3	160.13	—	—		—
18 5/8	87.5	473.08	130.21	11.05	450.98	446.22	125.91	33.6	—	39.25	—
20	94	508	139.89	11.13	485.7	480.97	136.38	20.5	27.11	24.78	—
20	94	508	139.89	11.13	485.7	480.97	136.38	20.61	27.26 g 24.27 17.84	24.78	—
20	106.5	508	158.49	12.7	482.6	477.82	155.13	18.22		22	—
20	133	508	197.93	16.13	475.7	470.97	195.66	13.03		16.02	—
NOTE See also Figures D.1, D.2, and D.3.
a Labels are for information and assistance in ordering.
b Nominal linear masses, threaded and coupled (Column 4) are shown for information only.
c The densities of martensitic chromium steels ( L80 Types 9Cr and 13Cr) are less than those of carbon steels; The masses shown are therefore not accurate for martensitic chromium steels; A mass correction factor of 0.989 shall be used.
d Mass gain or loss due to end finishing; See 8.5.
e Drift diameter for most common bit size; This drift diameter shall be specified in the purchase agreement and marked on the pipe; See 8.10 for drift requirements.
f Based on 758 mPa minimum Yield strength or greater.
g Based on 379 mPa minimum yield strength.